Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across San Bernardino
Gate repair in San Bernardino comes down to two things: knowing how Cajon Pass wind loads fatigue hardware, and knowing which older gates are worth saving. That’s what we do. Kensington Gate Repair handles broken swing gates, sagging chain-link, bent iron, seized hinges, dead operators, and control boards that no longer respond. If your gate won’t open, won’t latch, drags on the concrete, or groans when the operator cycles, call (833) 320-4513 and we’ll send a gate specialist to your address in San Bernardino, not a general handyman.
Why Kensington Gate Repair Is San Bernardino’s Preferred Gate Repair Company
We work on virtually every major gate brand, and we’ve spent enough time in the 92401, 92403, and 92404 zip codes to know what San Bernardino’s climate does to gate hardware. Homeowners near the foothills and along the Cajon Pass corridor call us after every Santa Ana event because their hinges are fatigued, posts have shifted, and latches won’t catch. That’s our normal workday here. We’re electric gate specialists, not a general contractor who occasionally tightens a hinge. Our team is led by Allen Prescott, and every job quote is agreed before any work starts. When you call Kensington, you get a diagnosis you can trust the first time, because we already know the failure patterns this city produces.
We serve both residential and commercial properties across San Bernardino, from mid-century tract homes with original chain-link gates to pre-1970 properties near the base of the foothills with iron gates hung decades before current safety standards existed. If you manage an HOA or commercial lot, we handle loop detectors, safety edges, keypads, and access systems too. One call covers repair and installation.
Styles & brands we work with
Iron Gate Repair in San Bernardino
Iron Gate Repair in San Bernardino usually starts as a latch or sag complaint, but the actual failure is often lower: hinge posts set in shallow concrete that has shifted in the region’s expansive clay soil. When a post leans even half an inch, the panel drags, the latch stops aligning, and every cycle stresses the hinges further. We reset footings, true the post, and re-hang the panel so it swings clean. Typical iron gate repair in San Bernardino runs $220 – $480 depending on post condition and whether we need to cut and re-weld hinge barrels or straighten a bent stile.
Weld and Hinge Work on Older Iron
Wind-fatigued welds are the most common iron gate failure we see after fall and winter gust events. A 50 mph blast off the Cajon Pass stresses the joint between stile and rail repeatedly, and older welds crack. We grind out the failed weld, re-weld it, and often add a gusset so the same failure doesn’t come back next season.
Post Resetting and Sag Correction
If the post moves, tightening the hinge bolts does nothing. We remove the panel, dig out the old footing, reset the post with proper depth and anchoring, and re-hang the gate. This is the single most effective repair on older San Bernardino properties where original posts were set shallow.
Sliding Gate Repair in San Bernardino
Sliding Gate Repair in San Bernardino frequently means a gate that stops mid-travel, binds on the track, or won’t respond to a remote. We see bent chain-link frames after wind events, worn rollers that chew up the track, and legacy operators with control boards that have finally failed. Typical sliding gate repair in San Bernardino runs $260 – $540, with track work and roller replacement at the higher end when the gate has been grinding for months.
Track and Roller Replacement
Sliding gates ride on rollers and a floor track that collects dirt, gravel, and wind-blown debris. When rollers seize, the gate drags and overloads the operator. We replace the rollers, clean or replace the track section, and adjust the guide rollers so the gate moves with one hand rather than leaning its full weight on the motor.
Operator and Limit Switch Service
If the gate opens partway and reverses, or slams into the open stop, the limit switches or control board are the likely culprits. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. For older units that are no longer supported by the manufacturer, we give you a straight answer: retrofit what’s safe, or replace the operator. No parts-pushing.
Trusted Brands We Service in San Bernardino
Your gate brand, our expertise. We work on virtually every major gate brand: LiftMaster, FAAC, BFT, Linear, and others. That matters in San Bernardino because so many mid-century homes still run original LiftMaster or Linear operators that local generalists won’t touch. We’re a dedicated Gate Repair company that works on competing brands without loyalty to any single manufacturer. What fits your system is what we recommend. Our team carries common control boards, safety photocells, and capacitor kits on the truck, so many San Bernardino callouts are completed in one visit without waiting on parts.
Common Gate Repair Problems We See in San Bernardino Homes
- Hinge posts shifting in expansive clay soil. The original footing was poured shallow in the 1960s, and the clay under it expands and contracts seasonally. The post leans, the gate sags, and tightening hardware doesn’t help.
- Wind-fatigued welds and bent chain-link frames. Repeated 40 – 70 mph gusts off the Cajon Pass crack welds and bow lighter metal frames, especially after fall and winter Santa Ana events.
- Legacy operators with dead control boards. Older LiftMaster, Linear, and DoorKing units from the 1990s and early 2000s often stop responding to remotes or loop detectors when the board fails. Some can be retrofitted; some are done.
- Seized hinges from heat and dust. Inland summer heat dries out lubricant and bakes dust into hinge barrels. The gate groans, binds, and eventually the operator burns out fighting the resistance.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in San Bernardino, CA
What should you expect to pay? Here are real numbers for this market. A basic sag correction or hinge lubrication on a pedestrian gate runs $120 – $220. Iron gate post resetting with new footing runs $220 – $480. Sliding gate track and roller replacement runs $260 – $540. Operator board replacement for a legacy LiftMaster or Linear unit runs $180 – $420 installed, depending on the board. Full operator replacement, including safety edges and wiring, starts around $650 and goes up based on the system. Every quote is written and agreed before we start work, and estimates are free. Call (833) 320-4513 for an exact price on your gate.
We Also Serve Cities Near San Bernardino
Our team regularly works in San Bernardino and the surrounding communities of Muscoy, Highland, Loma Linda, and Rialto. If your property sits near the 210 or the 215 interchange, we can usually route a technician to you the same week. We know the gate stock and soil conditions across the whole corridor.
Serving San Bernardino, CA — Our Local Coverage Area
We’re based in the San Bernardino area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in San Bernardino
Call as soon as you notice the gate binding or dragging. A bent chain-link frame or fatigued weld gets worse with every cycle, and wind events in San Bernardino come in clusters. If the gate still moves, we can often straighten the frame and reinforce the weld points for $220 – $400. If you ignore it until the operator burns out, you’re looking at a full operator replacement on top of the frame repair. Call (833) 320-4513 and describe what you’re seeing; we’ll tell you whether it’s urgent.
Yes. We work throughout 92401, 92402, 92403, and 92404, including neighborhoods near the 210 corridor, downtown, and the foothill areas north of the 30th Street alignment. Response to San Bernardino addresses is usually within one to two business days for non-emergency calls.
We prioritize emergency calls where a gate is stuck open or won’t close, because a gate stuck open is a security problem for the whole property. Call (833) 320-4513 as early as possible and we’ll route a technician to your San Bernardino address on the next available run. We’re straightforward about timing: if we can’t make it today, we’ll tell you and give you the earliest slot.
San Bernardino runs about 10 – 15% below what you’d pay in Highland or Loma Linda for comparable work, mostly because many homes here have simpler chain-link and older iron gates rather than newer custom steel installations. Typical repairs here run $120 – $540. The big cost variable in San Bernardino is post resetting, since so many original posts were set in shallow concrete over expansive clay.
We stand behind our repairs. If the same hinge or weld fails within the warranty period, we come back and fix it at no charge. Wind-related failures are common here, which is exactly why we reinforce weld points and reset posts properly rather than doing a quick patch. Call (833) 320-4513 for details on your specific repair. Estimates are always free, and the price is agreed before any work begins.
Contact Kensington Gate Repair in San Bernardino
When a gate fails in San Bernardino, the wind and the soil have usually been working on it for years before it finally quits. We know the failure patterns. We know which repairs hold and which don’t. Call (833) 320-4513 for a free estimate and a straight answer on your gate. One call covers repair or full replacement, from diagnosis to installation.
Written by Allen Prescott, Owner at Kensington Gate Repair, serving San Bernardino from our Montclair base.